NEWS

Leading chinese undercarriage pars & Machinery part supplier

Aug 26,2026

Komatsu D65 Dozer Undercarriage Inspection and Parts Fitment Guide

A Komatsu D65 undercarriage cannot be identified accurately from the base model alone. Current D65-18 materials include EX, PX, WX and intelligent machine-control variants, with differences in track geometry, shoe width, ground contact and application. Inspection should therefore document both wear condition and the exact machine identity before replacement parts are selected.


Aug 26,2026

Cat 336 Excavator Undercarriage Inspection and Parts Fitment Guide

A Cat 336 undercarriage should be inspected as a complete wear system, not as a collection of isolated parts. The machine name alone is not enough for ordering because the 336 family spans different generations, build numbers, configurations and markets. A useful inspection therefore combines visible wear clues with the full model suffix, serial or PIN, existing part numbers, measurements and jobsite conditions.


Aug 25,2026

Dozer Equalizer Bar and Pivot Shaft Inspection: Uneven-Wear Clues

On many crawler dozers, an oscillating equalizer bar and pivot-shaft arrangement helps support and connect the tractor to the track frames while allowing controlled movement over uneven ground. Leaks, cracks, damaged pads, loose joints or abnormal frame position can affect stability and may contribute to uneven undercarriage wear, but they require model-specific inspection.


Aug 25,2026

Excavator Track Chain Dry Joint: Heat, Noise and Seal-Loss Inspection

A track-chain joint relies on the correct pin, bushing, seal and internal lubrication arrangement for its design. If one joint becomes unusually hot, noisy or stiff, it may no longer be moving like the neighbouring joints. These clues require a complete inspection because trapped debris, track adjustment, alignment and mating-component wear can create similar symptoms.


Aug 24,2026

Dozer Undercarriage Replacement Planning: Measure, Match and Schedule

A dozer undercarriage wears as an interacting system, but its parts do not always reach the same condition at the same time. The correct replacement plan therefore begins with measured wear and operating records—not a rule that every repair must be a single part or a complete set. Chain, sprocket, roller, idler, shoe and frame condition must be reviewed together.


Aug 24,2026

Excavator Undercarriage Maintenance for Demolition and Scrap Sites

Broken concrete, reinforcing steel, crushed aggregate and metal scrap create a different undercarriage risk from ordinary earthmoving. Sharp debris can damage shoes and hardware, packed fragments can restrict rollers, and repeated turning on hard material can concentrate wear. A demolition excavator therefore needs condition-based cleaning and inspection throughout the shift, supported by the exact operation and maintenance manual.


Aug 21,2026

Excavator Sprocket Wear Signs: Inspection and Replacement Planning Guide

The excavator drive sprocket works directly with the track-chain bushings. Tooth wear, chain pitch, track tension and the condition of mating undercarriage parts should be assessed together before deciding what to replace.


Aug 21,2026

How to Check Excavator Track Tension: Inspection Guide and Common Problems

Excavator track tension affects how the chain, sprocket, idler and rollers work together. This guide explains how to inspect track tension safely, what loose or tight-track symptoms may indicate, and why the exact machine manual must be used before adjustment.


Aug 20,2026

Excavator Undercarriage Measurements: A Parts Fitment Checklist

Excavator undercarriage parts can look almost identical while differing in pitch, link count, flange profile, mounting pattern or serial-range application. A reliable inquiry therefore starts with the machine identity, the installed part number, clear photographs and the correct component-specific measurements—not the model name alone.


Aug 20,2026

Bulldozer Track Alignment: Side Wear, Causes and Inspection Guide

A bulldozer track should travel through a controlled path formed by the sprocket, rollers, idler, guards and track frame. Bright side contact, uneven flange wear or repeated rubbing can indicate that the path is being disturbed, but these signs do not prove one cause. Alignment complaints require a complete comparison of both sides, the operating conditions and the machine's model-specific adjustment.


< 1...8910...30 >

Related Posts

How Should The Supporting Wheels Be Selected To Avoid Stepping On Thunder?

High-quality support wheels mainly depend on the performance of its steel. The material of the roller body is generally 50Mn, 40Mn2, (MN: synonymous with the element of manganese).

Carrier Wheels Are Suitable For Various Models At Home And Abroad

Sprocket wheels are mainly used in various crawler bulldozers, excavators, pavers, milling machines, rotary drilling rigs or other crawler machinery equipment at home and abroad.

Contact Us

E-mail :
sales@china-ysm.com

Phone/WhatsApp:
+86-18606961587

Address:
No.8 Binjiang Street, Binjiang Industrial Zone, Xiamei Town, Nan An City, Quanzhou City, Fujian Province, China

AW-18202131004